Find Jobs
Hire Freelancers

pin board 2012

min $5000 USD

Cerrado
Publicado hace más de 11 años

min $5000 USD

Pagado a la entrega
i am looking for a device to be made i have tried to do a few ways so far i tried with solenoid and coils. I have not been able to get it done due to cost. i need to have have a board of 400 pins that look a bit like a pin art toy. (they are arranged like a a grid 20 by 20) moved automatically I wish to be able to move some or all of the pins up or down at the same time and then the pins to stay in place I have tried to replace the pins with linear actuators but the cost sky rockets as each actuator costs 15 - 50 dollar x 400 =6k 30k So i need a cheap way to move the pins the cheapest way i can think of is to have a mechanical flick switch on the pin moving it up 1 mm at a time and another moving it down 1 mm at a time. by a device under the board . another is use a crayola twistable with the crayon replaced by a plastic bar and a plastic motor at the bottom with 10 spins should fully extend the bar. another is to have 3 tubes one inside other with middle one has magnet and insulation. Inner and outer have copper coils opposing each other seperated by insulation elec applied to inner coil pushes up middle tube and elec applied to outer tube puses down plastic tube by varing the power between both you can vary height of tube. I am sure there are other ways i am very open to otherways the target price of this board will be about 2k The pins will rise 100mm above the board and the board will be 200mm by 200mm ideally i would like less space between the pins. the pins should be square and between 9mm and 6mm wide. There is minimal load on the pins the board will need to be computer controlled with a simple interface where each pin can be numbered and each pin can be instructed to go to the required height. Every few seconds the board will be given a new set of heights for the pins to go to this should only take a few seconds. I am open to ways the pins can be moved but i will need a workable approach before i award the project. i will need six of these boards to be made so all can be controlled by the same computer at the same time.
ID del proyecto: 2384361

Información sobre el proyecto

8 propuestas
Proyecto remoto
Activo hace 12 años

¿Buscas ganar dinero?

Beneficios de presentar ofertas en Freelancer

Fija tu plazo y presupuesto
Cobra por tu trabajo
Describe tu propuesta
Es gratis registrarse y presentar ofertas en los trabajos
8 freelancers están ofertando un promedio de $7.463 USD por este trabajo
Avatar del usuario
Professional engineer with 25 years of Aviation industry and 15 years in engineering institute, can give elegant design, with a prototype.
$10.500 USD en 90 días
4,4 (24 comentarios)
5,1
5,1
Avatar del usuario
Dear Sir, I have 10 year experience on analog design, audio system, power electronics, digital motor control, inverters, converters, DC-DC converters, power distribution sysetms, PCB design, circuit simulation, system simulation. The document which shows my background is attached. It shows my ability to make your work. I have gratuated Hacettepe University electric and Electronics engineer. I have passed several courses until now. My university is one of 500 th university in the world. To discuss details of project, you can ask me any questions. By talking we can agree on terms and conditions of your Project. I hope you will give oppurtinutiy to show my intelligence and reasoning. Regards. Beta
$7.500 USD en 100 días
4,7 (9 comentarios)
4,8
4,8
Avatar del usuario
Sir, We are willing to work on this project.
$5.000 USD en 90 días
0,0 (0 comentarios)
0,0
0,0
Avatar del usuario
Hi, We are interested in this project, kindly reply if you are interested.
$5.000 USD en 10 días
0,0 (0 comentarios)
0,0
0,0
Avatar del usuario
Hello I'm a Final Year Undergraduate Student - Electrical Engineering Majors. I have a few ideas which I can discuss with you in detail, if you like. I've worked on a number of sophisticated mechanisms and their electronic control, using either FPGAs and MCUs. Hope to hear from you soon. Regards Zaid A.
$8.000 USD en 75 días
0,0 (0 comentarios)
0,0
0,0
Avatar del usuario
hello, We have a team of engineers from automation and robotics, Mechatronics,Electronics , electrical and mechanical background and can work on the project that u have posted. Hoping to get the project from your side. thanks Regards Team Xtrmengineers
$10.000 USD en 100 días
0,0 (0 comentarios)
0,0
0,0
Avatar del usuario
Hello Sir, We have done the simillar project in our company,but it has not computer interfaced.I will give you the brief work out on this project by within couple of days. Thank's in advance, Lokesh.
$7.500 USD en 60 días
0,0 (0 comentarios)
0,0
0,0
Avatar del usuario
Hi, I would like to ask you some questions in the PM so we can clear some details before I place my final bid. My father and uncle are interested in this job and they have great experience in the required skills. Check your PM
$7.000 USD en 80 días
0,0 (0 comentarios)
0,0
0,0

Sobre este cliente

Bandera de IRELAND
Dublin, Ireland
4,9
62
Forma de pago verificada
Miembro desde dic 7, 2006

Verificación del cliente

¡Gracias! Te hemos enviado un enlace para reclamar tu crédito gratuito.
Algo salió mal al enviar tu correo electrónico. Por favor, intenta de nuevo.
Usuarios registrados Total de empleos publicados
Freelancer ® is a registered Trademark of Freelancer Technology Pty Limited (ACN 142 189 759)
Copyright © 2024 Freelancer Technology Pty Limited (ACN 142 189 759)
Cargando visualización previa
Permiso concedido para Geolocalización.
Tu sesión de acceso ha expirado y has sido desconectado. Por favor, inica sesión nuevamente.