CAN bootloader for Freescale MPC5634

$750-1500 USD

Cerrado

Publicado

hace más de 7 años

$750-1500 USD

Pagado a la entrega

Develop and produce C source code for the Freescale MPC5634 microcontroller using the TRK-MPC5634 evaluation board. The software will have two functions: 1) At boot up time, if a PC requests the microprocessor memory to be programmed over CAN bus, the bootloader will handle firmware and data area programming. The Windows PC software, USB-CAN interface, programming communications protocol will all be provided. These are already developed and working. The firmware and data areas will be arranged in the on-board Flash EEPROM of the MPC5634 as listed in the memory map below. The bootloader must communicate with the PC software over CAN bus, erase Flash EEPROM sectors as required and write the binary data received from the PC to Flash memory. The bootloader will be able to support CAN bus speeds of 1Mbit/s, 500kbit/s and 250kbit/s. Memory Map Bootloader 0-0xffff Data1 0x10000-0x1ffff Data2 0x20000-0x3ffff Firmware 0x40000-0xfffff 2) If programming is not required at boot up time, jump to the start of the firmware area and allow the system to boot up normally. The datasheet for the TRK-MPC5634 evaluation board is attached to this document. The evaluation board includes Codewarrior integrated development environment with JTAG debugging and programming so includes all required hardware and software to complete the project. The deliverable of this project is the completed C source code for the bootloader developed using Freescale Codewarrior.

C Programming

Embedded Software

ID del proyecto: 11724588

Información sobre el proyecto

8 propuestas

Proyecto remoto

Activo hace 7 años

¿Buscas ganar dinero?

Dirección de email

Beneficios de presentar ofertas en Freelancer

Fija tu plazo y presupuesto

Cobra por tu trabajo

Describe tu propuesta

Es gratis registrarse y presentar ofertas en los trabajos

8 freelancers están ofertando un promedio de $1.415 USD por este trabajo

@Yknox

Hi, I am Eric Wang, Software Engineer in China. I've just read your job posting and I’m very interested. I'm a certificated freelancer with almost 600 good reviews from clients. I have experienced knowledge in every part of Software Engineering. I know how to bring your idea alive and communication well. I never disappoint my clients and I’m able to lead your project to success and troubleshoot problems. I am sure these will reflect in my past results. Please contact me if I am a match for you are looking for. Best Regards, Wang

$3.000 USD en 20 días

4,9

(414 comentarios)

8,4

@ibrahimdanish

Hi, I am very much interested in your project as I believe I have the expertise, knowledge, skills and tools to do your project. I am embedded software developer with more than 7 years of experience of professional embedded software development. Please take a look onto my profile to know more about me. I have quite a lot experience of automotive embedded systems based on Freescale MPC5516/17 . I have worked with CAN bus right from the creating CAN frames to writing CAN drivers and up to the application level to implement various CAN based protocols like ISO14229 etc for software download, read/write parameters and fault codes. I have worked on various CAN hardware /software tools such as PCAN, CANAnalyzer, CANDb editer, BUS Master etc. I believe I am quite familiar with your project as I I have also worked on primary and secondary bootloader for MPC5516/17 over CAN. If you choose me for this project, I will buy the TRK-MPC5634M board. My recent freelance projects that might tell you my knowledge, 1. STM32F415 based FATFs to read/write SD Card (both SDIO and SPI) 2. STM32F429 based FATFs to read/write USB mass storage 3. STM32F100 based sesnor board (Reads sensor using 24bit ADC over SPI, and send reading to PC suing FT232 USB chip) 4. STM32F105 based dual channel CAN transmitter . 5. STM32F107 based dual channel CAN to Ethernet converter. Looking forward to hearing from you soon to discuss the project in detail. Ibrahim

$1.666 USD en 20 días

4,8

(9 comentarios)

5,7

@prashushinde9

Hello, I understood the initial scope of this project. Although i want to discuss further this job in order to prepare the final concept for this project. After Complete discussion over the call or in chat, i will prepare following things for you - Technical Project Proposal - Flow chart for this Project - Execution plan (Step by step procedure with explanation how and at what that we are going to execute a particular task)

$1.546 USD en 40 días

5,0

(1 comentario)

3,1

@stockmarketwaves

I am an embedded software veteran for 18 years. Direct work experience of bootloader, JTAG resident RAM program and script programming experience.

$1.111 USD en 20 días

0,0

(0 comentarios)

0,0

@romanm11

Hello, I have experience with different MCU, toolchains and embedded SDK. I can use different hardware tools to test and troubleshoot issues. A good skills in reverse engineering should help me also. I'm looking forward to do business with you. Sincerely yours, Roman.

$1.111 USD en 20 días

0,0

(0 comentarios)

0,0

@tarungupta2309

I have written a boot loader for Embedded Linux for SH Family Processor in C-Language. I have also worked in CAN Bus for Car Navigation System. I can deliver this work within time and as per your expectation.

$1.250 USD en 20 días